Automatic Technology Australia Elite Instalační manuál

AUTOMATIC TECHNOLOGY AUSTRALIA PTY LTDOWNERS COPYWarning: It is vital for the safety of persons to follow all instructions. Failure to comply with th

MOUNTING CONTROL BOX10MOUNTING CONTROL BOXCAUTION: DO NOT USE ANY CABLES WHICH CARRYGREEN/YELLOW WIRES AS THIS SIGNIFIES EARTH,AND DOES NOT COMPLY WI

11ELECTRICAL CONNECTION - SINGLE LEAFFIG. 10FIG. 11SINGLE LEAF INSTALLATIONMotor on Left SideSINGLE LEAF INSTALLATIONMotor on Right Side

12ELECTRICAL CONNECTION - DUAL LEAFFIG. 12FIG. 13DUAL LEAF INSTALLATIONLeft side opens firstDUAL LEAF INSTALLATIONRight side opens first

SETTING OBSTRUCTION FORCECHECKING LIMITS POSITIONSWARNING: If gates require sync delay - Switch 1 must be set toON before fine tuning limits.1. Re-eng

1. COMMON TERMINAL FOR (2) TO (7) BELOW.2. PHOTO-ELECTRIC SAFETY BEAM INPUT (N/C).3. OPEN CONTROL INPUT (N/C).4. STOP CONTROL INPUT (N/C).5. CLOSE CON

15AUTO-CLOSE MODEAuto-close mode automatically closes the gate after a preset timeonce the gate has reached its desired open position. The controllers

MODE SELECTIONIf the P.E. input is configured to stop the gate during opening orclosing, then the gate can auto-close from a midway position. Thisfeat

17CODING TRANSMITTERSCODING TRANSMITTERS INTO RECEIVERTransmitters can be programmed into the gates receiver to do twofunctions: the full Open/Stop/Cl

18ACCESSORIESCONTROL AND SAFETY INPUT TERMINALSFig. 19 shows the control and safety input terminals and theirswitch contacts. Note that the P.E., OPN

19BATTERY BACK UPAn optional battery backup system is available so that the gate canbe operated (for a limited time) in the event of mains power failu

TROUBLE SHOOTING20Gate does not open or close Check that power is still available at mains power point.Check that Control Box is plugged into mains po

PARTS LIST21WHEN ORDERING SPARE PARTS PLEASEQUOTE THE ORDER CODE NUMBERTO YOUR YOUR INSTALLER/DEALER

WARRANTY AND EXCLUSION OF LIABILITY1. This warranty is an addition to any non-excludable conditions or warranties that are implied into this contract

NOTES23Purchased From ___________________________________ Phone ______________________Installed By _______________________________________ Date ______

AUTOMATIC TECHNOLOGY AUSTRALIA PTY LTDABN 11 007 125 36817-19 Advantage Rd, Highett, Victoria, Australia 3190Tel: +61 3 9532 2788 Fax: +61 3 9532 27

Automatic Technology Australia Pty Ltd to the extent that such may be lawfully excluded hereby expressly disclaims allconditions or warranties, statut

IMPORTANT SAFETY INSTRUCTIONS4For ADDITIONAL SAFETY protection weSTRONGLY recommend the fitting of a Photo ElectricBeam. In most countries Photo Elec

5FEATURESThank you for purchasing the ATA EliteSwing Gate Opener. This opener isdesigned to suit residential hinged swinggates. The components and mat

Kit Contents6ITEM DESCRIPTION QTY1. Drive Unit 12. Control Box 13. Control Box Mounting Bracket 44. PTX-4 Keyring Transmitter 25. Transmitter Battery

7DRIVE UNIT INSTALLATIONThe ATA Elite swing gate opener is designed to operate most residential swing gates. The gates must be in good working conditi

DISENGAGED8DRIVE UNIT INSTALLATIONMOUNTING DRIVE UNIT1. Mount drive unit using four (4) 10mm loxins or dynabolts. 2. Make sure that the Drive Unit is

9INSTALLING DRIVE UNIT ARMSFIG. 5AFFIXING ARMS AND BRACKETS TO GATE1. Position gate in close position.2. Attach drive arm extension to drive arm (fixe